XP6 Hydro Penis Pump 6 Suction LED Display 100% Waterproof

A hydro penis pump is a type of vacuum erection device (VED) that can use both air and water instead to create a vacuum around the penis. It operates on the same principle as traditional air-based penis pumps but utilizes air or water to generate the negative pressure needed for penile engorgement and erection.

Using a water penis pump, also known as a hydro penis pump, involves several steps to ensure safety, comfort, and optimal results. Here's a general guide on how to use a water penis pump:

1. Prepare the Pump: Before using the pump, ensure that it is clean, assembled correctly, and in good working condition. Check for any damage or defects.
2. Fill with Water: Fill the cylindrical tube (the cylinder) of the pump with warm water. The water should be at a comfortable temperature, not too hot or too cold.
3. Apply Lubricant: Apply a small amount of water-based lubricant to the base of your penis. This helps create a better seal between the pump's cylinder and your skin, enhancing comfort and effectiveness.
4. Insert Penis into the Cylinder: Gently insert your flaccid penis into the water-filled cylinder of the pump. Make sure the base of the cylinder forms a snug seal against your body to prevent water leakage.
5. Start Pumping: Begin pumping the device using the hand pump mechanism or electric pump, depending on the type of hydro penis pump you have. Pump steadily to create a vacuum inside the cylinder. You should feel a slight pulling sensation as the vacuum draws blood into the penile tissues.
6. Monitor Pressure: Pay attention to the pressure inside the cylinder. Avoid over-pumping, as excessive pressure can cause discomfort, bruising, or injury. If you feel any pain or discomfort, release the pressure immediately by using the release valve.
7. Maintain Erection: Once you've achieved the desired level of pressure and your penis is erect, continue to maintain the vacuum for a few minutes. This allows blood to flow into the penile tissues and helps sustain the erection.
8. Release Vacuum: When you're ready to release the vacuum, use the release valve on the pump to gradually release the pressure inside the cylinder. Do this slowly and gently to avoid sudden changes in pressure.
9. Remove Pump: After releasing the vacuum, carefully remove the cylinder from your penis. You may need to push the base of the cylinder to break the seal gently.
10. Engage in Sexual Activity: With the erection achieved using the pump, you can engage in sexual activity as desired. Remember to remove any accessories, such as constriction rings, when no longer needed.
11. Clean and Store: After use, clean the pump and its components following the manufacturer's instructions. Ensure proper hygiene and store the pump in a dry, safe place.

It's crucial to use a water penis pump responsibly, follow the manufacturer's instructions, and avoid excessive pressure to prevent discomfort or injury. If you experience any pain, discomfort, or unusual reactions, stop using the pump immediately and consult with a healthcare professional.

Cleaning and maintaining a hydro penis pump is crucial to ensure hygiene, longevity, and optimal performance. Here are the general steps to clean and maintain a hydro penis pump:

1. Disassemble the Pump: After each use, disassemble the pump by separating the cylinder from the pump mechanism and any attachments or accessories.
2. Empty Water and Rinse: Empty the water from the cylinder and rinse it thoroughly with warm water. Ensure that all residues, lubricants, or bodily fluids are removed from the cylinder and other components.
3. Use Mild Soap: Apply a mild, unscented soap to a soft cloth or sponge and gently clean the surfaces of the pump, cylinder, and attachments. Pay attention to any crevices or hard-to-reach areas where dirt or debris may accumulate.
4. Rinse Again: After cleaning with soap, rinse all parts again with warm water to remove any soap residue completely. Ensure that no soap remains on the surfaces, as it can cause irritation or discomfort during future use.
5. Dry Thoroughly: Use a clean, dry cloth or towel to pat dry all parts of the pump and its components. Allow them to air dry completely before reassembling or storing to prevent the growth of mold or bacteria.
6. Inspect for Damage: Periodically inspect the pump and its components for any signs of wear, damage, or deterioration. Check the sealing ring or gasket for cracks or tears, and replace it if necessary to maintain a proper seal.
7. Store Properly: Store the cleaned and dried pump and its components in a cool, dry place away from direct sunlight. Avoid storing it in a humid environment or near chemicals that could damage the materials.
8. Use Water-Based Lubricant: When using the pump, always use a water-based lubricant specifically designed for use with hydro penis pumps. Avoid using oil-based or silicone-based lubricants, as they can damage the pump's materials.
9. Avoid Harsh Cleaners: Do not use harsh chemicals, solvents, or abrasive cleaners to clean the pump, as they can damage the materials and affect its performance.

By following these steps and practicing regular cleaning and maintenance, you can ensure that your hydro penis pump remains clean, hygienic, and functional for an extended period. If you have specific instructions from the manufacturer, be sure to follow those guidelines as well.